Chimney, skylight & wall flashing referrals

Flashing & Chimney Leak Repair in Draper, UT

Describe your chimney or flashing leak online and we will connect you at no charge with an independent local roofing pro in the South Salt Lake Valley.

Why flashing transitions cause more South Valley roof leaks than field shingles

Across Draper, Sandy, Cottonwood Heights, Holladay, and South Jordan, custom residential architecture creates dozens of roof-to-wall intersections: stone-veneer fireplace chases, stucco dormers, multi-material standing-seam metal porch roofs meeting asphalt gables, and wide skylights overlooking the Wasatch Range. Meanwhile, older brick chimneys in Midvale, Murray, White City, and Millcreek face decades of freeze-thaw mortar cracking. Even when field shingles have ten years of life left, one improperly lapped piece of step flashing or a missing kickout diverter will funnel snowmelt directly behind interior drywall.

Where flashing fails most often on Draper and South Salt Lake Valley roofs

  • Surface-caulked chimney counter-flashing: Instead of cutting a reglet groove into brick or stone masonry and tucking metal counter-flashing inside, shortcuts rely on exterior sealant beads. Under Utah's sun and winter freeze-thaw cycles, surface caulk splits within a few seasons and lets water run straight behind the base flashing.
  • Missing or undersized chimney crickets (saddles): On wide chimneys positioned on the lower half of a steep SunCrest, Corner Canyon, or Cottonwood Heights slope, heavy snow slides and drifts pile directly behind the upslope chimney face. Without a properly framed and metal-flashed cricket to divert runoff sideways, pooled meltwater backs up under shingles.
  • Stucco and stone-veneer kickout omissions: At the lower end of a roof-to-wall intersection, a kickout (diverter) flashing must direct water off the roof edge and into the gutter. Without it, runoff flows down the side of stucco or cultured stone cladding, saturating wall sheathing invisibly.
  • Multi-material and dead-valley junctions: Where a steep composite roof dumps into a low-slope metal porch roof or a flat section between dormers, standard shingle laps cannot handle standing snowmelt. Continuous soldered or hemmed sheet-metal pans and self-adhering high-temp membranes are critical.

Code compliance and contractor licensing for flashing repairs

2021 IRC Section R905 mandates corrosion-resistant flashing at wall-and-roof intersections, gutters, changes in roof slope or direction, and around roof openings, with kickout flashing where a lower roofline meets a vertical sidewall. Localized flashing renewal qualifies as a maintenance roof repair under Draper City's Roofing Permit Policy (no city permit required unless tied to a broader roof recover or replacement). Remember that if a combined masonry-and-flashing repair crosses $7,000, Utah Code Section 58-55-305(1)(h) requires an active Utah DOPL license (S280, B100, or R100), and jobs over $3,000 require at minimum a DOPL Affirmation of Exemption with liability insurance.

Connect with an independent roofer who fabricates proper metal flashing

Submit our online estimate form describing your chimney material (brick, cultured stone, stucco, or wood siding) and where water appears. We forward your request at no charge to an independent local roofing professional serving Draper and the South Salt Lake Valley.

Get a Free Estimate

Areas We Cover in South Salt Lake Valley

Flashing and chimney repair scopes handled by local pros

Lasting flashing repairs replace failed metal and underlayment rather than smearing temporary tar over joints. Common scopes include:

Chimney Apron, Step & Reglet Counter-Flashing

Installing individual L-shaped step flashings woven with every shingle course and cutting clean mortar reglets for overlapping metal counter-flashing.

Chimney Cricket (Saddle) Fabrication

Framing and flashing a peaked diverter behind wide upslope chimneys so heavy Draper and east-bench snowmelt splits around the chase instead of pooling.

Kickout & Sidewall Stucco/Stone Flashing

Retrofitting proper kickout diverters and sidewall step flashing where roof planes terminate against stucco, fiber-cement, or stone-veneer walls.

Multi-Material Roof-to-Roof Transitions

Rebuilding leaking transition pans where architectural shingles meet standing-seam metal accents, concrete tile skirts, or low-slope patio tie-ins.

Skylight & Mechanical Curb Re-Flashing

Replacing rusted or bent skylight step-flashing kits, head-wall diverters, and furnace/evaporative-cooler curb collars with ice-and-water underlayment.

Flashing and chimney leak scope and inspection reference

Flashing AssemblyTypical South Valley Failure ModeInspection & Quote Note
Brick or stone chimney base & counter-flashingSplit surface caulk, missing reglet cuts, rusted apron pan, or deteriorated mortar cap.Requires on-roof check of masonry condition, shingle overlap, and upslope width; quoted on site.
Stucco or stone-veneer dormer sidewall & kickoutMissing kickout diverter sending runoff behind stucco lath or siding sheathing.Contractor inspects wall-to-roof transition and surrounding siding clearance before quoting.
Chimney cricket or dead-valley metal panSnowpack drifting behind wide chases on steep SunCrest, Sandy, or Cottonwood Heights slopes.Custom metal fabrication and ice-and-water membrane tie-in scoped after exact field measurement.
Skylight or roof-penetration curb flashingAged rubber gaskets, unstepped flashing kits, or condensation inside skylight shafts.Verify skylight model, curb height, and IRC R905 flashing clearances during on-site inspection.

Flashing complexity varies sharply between simple pipe collars, masonry reglet work, and custom multi-material transitions. Independent licensed contractors provide written quotes after inspecting your roof in person.

Why Use a Referral for Flashing & Chimney Leak Repair?

Addresses custom Draper architectural complexity

Built for South Valley homes with stone chases, stucco dormers, multi-plane valleys, and mixed metal-and-shingle transitions.

Separates roof flashing from masonry or siding leaks

An on-site inspection checks step flashing, reglet joints, chimney crowns, and attic framing so the actual water path gets fixed.

Transparent independent referral model

Roofing Repair Draper never charges homeowners for a referral and never inflates contractor quotes.

Direct Utah DOPL verification reminders

Verify any independent contractor's S280, B100, or R100 license at secure.utah.gov/llv/ before authorizing custom metal or chimney work.

Contact Us Today for a Free Estimate

Describe your chimney, skylight, or wall flashing leak online to connect at no charge with an independent local roofing pro.

Get a Free Estimate

Free — no obligations

How flashing and chimney leak repair proceeds

1. Share transition details online

Tell us your city, chimney or wall material (brick, stucco, stone, siding), and where moisture appears indoors.

2. Local roofer reaches out

We pass your inquiry to an independent South Salt Lake Valley roofing professional to arrange an on-site visit.

3. Roof-to-wall and attic inspection

The contractor lifts adjacent shingles as needed, inspects step and counter-flashing, checks masonry joints, and measures custom metal needs.

4. Written quote and decision

Review the itemized metal-and-underlayment scope, confirm Utah DOPL credentials, and decide whether to proceed.

Roofing Repair Services Available in Draper, UT

Get a Free Estimate